Concrete Sand Delivery in San Antonio, TX

Concrete Sand in San Antonio, TX: Built for Hill Country Soil and Heat

San Antonio sits on a tough patch of ground for builders. The expansive clays of the Blackland Prairie shrink and swell with every wet and dry cycle, the limestone shelf of the Hill Country lurks just under much of the north side, and summer heat bakes any slab you pour. Concrete sand is the aggregate that helps you work with all of it. Graded from 0 to 3/8 inch in a tan to gray tone, this coarse washed sand is the fine aggregate behind solid concrete, the bedding under durable pavers, and the body of dependable masonry across the San Antonio-New Braunfels metro. MyGravelBuddy delivers it bulk by the ton, starting at $101 per ton.

What makes concrete sand right for San Antonio is its grit. The angular, well-graded particles knit together and create the friction and void structure cement paste needs to cure strong. On clay-heavy lots, a properly bedded and drained base built on the right sand resists the movement that cracks slabs and heaves patios. That is the difference between a driveway that lasts and one that telegraphs every drought-flood cycle within a few seasons.

Why San Antonio Crews Reach for Concrete Sand

Across the metro, concrete sand shows up on four core jobs:

• Concrete mixing. It is the fine aggregate blended with stone and Portland cement for slabs, footings, mow strips, and the sidewalks that crews pour year round here.
• Paver bedding. A screeded one inch layer sets a flat, drainable bed for the flagstone and concrete pavers that define San Antonio outdoor living, from Alamo Heights patios to Stone Oak pool decks.
• Pipe bedding. Its free-draining grade cradles utility and drainage pipe without point loading, important on rocky north-side trenches.
• Masonry work. For parge coats, scratch coats, and bulk mortar bodies, concrete sand brings strength where fine finish is secondary.

Smart crews match the sand to the task. Fine joint work and stucco finishes call for Mason Sand, while raising grade and backfilling non-structural areas is a job for cheaper Fill Sand. Under a heavy driveway or pool deck, a compacted layer of Paver Base carries the structural load and concrete sand goes on top as the bedding course. Picking the right material for each layer keeps San Antonio projects on budget and off the callback list.

Local Delivery and Lead Times in San Antonio

We run bulk dump deliveries across every San Antonio zip, from downtown and Southtown out to the 1604 loop, and on into the metro toward New Braunfels and up the I-35 corridor to Austin, about 74 miles north, and Round Rock near 89 miles. Single-ton orders generally arrive in 1 to 2 business days. Loads of 6 tons and up frequently land same or next day, and full 16-ton loads move on our scheduled routes. San Antonio’s spread-out footprint actually works in your favor: most neighborhoods have driveway and side-yard access that lets us place a full tri-axle load close to where you need it. Let us know about gates, low limbs, and septic fields when you order so we can spot the pile cleanly.

How Much Concrete Sand Do You Need?

Concrete sand is sold by the ton, and at roughly 2,700 pounds per cubic yard it works out near 1.35 tons per yard. As a working rule, a one-inch screeded paver bedding layer covers about 300 to 320 square feet per ton. So a 720 square foot back patio in Schertz needs roughly 2.25 tons, call it 3 tons to be safe. For concrete, a 20 by 20 foot slab at 4 inches deep is about 5 cubic yards of finished concrete, and concrete sand makes up a large share of that volume as fine aggregate. Round up your sand order; a short load that stalls a pour in 100-degree heat is a far bigger problem than a little leftover sand.

San Antonio Pricing Context

Bulk concrete sand starts at $101 per ton delivered in San Antonio, with the rate falling as your load grows. Our three delivery tiers break down as follows:

• 1 ton minimum: $136 per ton plus a $263 delivery fee, arriving in 1 to 2 business days. Good for small repairs and top-ups.
• 6 ton minimum: $122 per ton plus a $141 delivery fee, with same or next day delivery. The practical pick for a typical patio or driveway base.
• 16 ton minimum: $101 per ton with free delivery. The best value for full pours, big hardscape jobs, and contractor stocking.

The biggest savings come at the 16-ton tier, where the delivery fee drops to zero and the per-ton rate hits $101. On a clay lot where you want to build a generous, well-drained base, ordering up to that tier often costs less per square foot than splitting smaller loads. If you are running a multi-phase build along the I-35 corridor, consolidating into one 16-ton drop usually beats several small hauls.

Placement and Installation Tips

Concrete sand performs when it is screeded, not just dumped. For paver beds, set screed rails to a true one inch and pull a straight edge for a flat setting layer. Do not compact the bedding sand before laying pavers; compact afterward with a plate so the units seat evenly. In San Antonio heat, keep batching sand tarped and shaded, since hot, dry sand and fast evaporation can rush your set and weaken the slab. For pipe trenches, place sand in lifts and tamp lightly so the pipe is supported but not crushed by the rocky backfill common up north.

Seasonal Notes for Texas

San Antonio’s calendar is less about frost and more about heat and water. Summer pours need early-morning starts, shaded sand, and attention to curing, because midday slabs lose moisture fast and crack if you let them flash off. Spring and fall are prime hardscape seasons, and that is when our routes fill up with patio and driveway loads across the metro. The real soil challenge is the wet-dry swing: long Texas droughts shrink the clay, then heavy storms swell it, and that movement is what cracks poorly based slabs. Build deeper, well-drained bases on expansive lots, and time your work so the base goes in and gets compacted before a big rain saturates the subgrade. Order ahead in spring when demand from San Antonio, New Braunfels, and Austin crews stacks our schedule. Mild winters mean we deliver concrete sand year round, so there is rarely a season you cannot get your jobsite stocked.

From a homeowner squaring up a backyard near the Medical Center to a contractor pouring slabs out toward Corpus Christi, MyGravelBuddy keeps clean, consistent concrete sand moving to San Antonio jobsites on a schedule that beats the heat.

About Concrete Sand

Concrete sand is a coarse, washed sand graded from 0 to 3/8 inch, tan to gray in color, with an angular particle shape that makes it the standard fine aggregate for structural concrete. Sold by the ton and weighing roughly 2,700 pounds per cubic yard, it is among the most versatile aggregates on any jobsite.

The defining property of concrete sand is its gradation. Because particle sizes spread across a range rather than sitting at one fineness, they pack with a controlled void structure that cement paste fills and binds. That gradation gives finished concrete its compressive strength and durability. The same coarse, free-draining nature makes concrete sand an excellent paver setting bed and a clean cradle for utility and drainage pipe.

Compared with finer products, concrete sand is engineered for load rather than finish. Mason Sand is softer and finer, tuned for smooth mortar joints, stucco, and tight masonry. Fill Sand is an economical, less-processed material for raising grade and backfilling non-structural areas. Paver Base, a crushed and graded stone product, carries the structural sub-base beneath a hardscape, with concrete sand screeded on top as the final bedding layer. Used together, these materials build a base system that holds up.

Concrete sand is washed to strip out silt, clay, and organic fines, so it batches cleanly and drains freely. It works in standard concrete mixes, mortar bodies, parge and scratch coats, pipe and conduit bedding, and as the setting course under brick, flagstone, and concrete pavers. Its strength, drainage, and consistency make it the dependable choice wherever a project needs sand that performs under pressure rather than simply filling space.

What Concrete Sand costs in San Antonio

Around San Antonio, concrete sand is quoted by the ton with delivery layered in based on distance from the closest yard. Pricing in San Antonio starts at $101 per ton on full-truck loads, which works out to roughly $136 per cubic yard at the typical density of 2700 lb per yard. Plan on roughly 80 sq ft of coverage per ton at 3 inches deep, which puts a single-car driveway in the 4 to 8 ton bracket. San Antonio pricing sits a touch above the TX state average, which is what we see across other product-loc rows we publish.

How crews use Concrete Sand in San Antonio

San Antonio contractors keep concrete sand on the order sheet for a short list of standard installs. Top of the list is pipe bedding, where the material is rolled out in tight urban lots and infill builds and screeded to grade. Right behind that is base course gravel, common in dense neighborhoods where curb access is short and often paired with edging or fabric below the lift. San Antonio sits at about 1,495,295 residents, which means we see steady weekday traffic from landscape crews and weekend pickups from owner-builders.

Delivery day in San Antonio

Delivery in San Antonio runs out of the nearest pit; you get a two hour arrival window the evening prior and a call when the driver leaves the scale. Plan for 12 ft of clear path for a tandem and 14 ft for a tri-axle, plus a level area at the dump point so the bed lifts straight. Standard lead time on this lane is Mon-Sat, with same-day windows held open for orders that hit the desk before 11 AM and clear payment.

Delivered pricing in San Antonio

Estimate how much you need